12:49 AM
Unknown
1
Refer to the exhibit. A router, the table of which is shown, receives a packet that is destined for
192.168.9.4. How will the router treat the packet?
It will drop the packet.
It will forward the packet via FastEthernet 0/1.
It will forward the packet to the next hop address.
It will forward the packet to 172.16.2.0
2
Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list
correctly identifies the component or protocol used at each numbered stage of the diagram?
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA
3
During the encapsulation process, what identifiers are added at the transport layer?
source and destination IP addresses
source and destination MAC addresses
source and destination port numbers
source and destination channel identifiers
4
Refer to the exhibit. Host C is able to ping 127.0.0.1 successfully, but is unable to communicate with hosts A and B in the organization. What is the likely cause of the problem?
Hosts A and B are not on the same subnet as host C.
The IP addresses on the router serial interfaces are wrong.
The subnet mask on host C is improperly configured.
The FastEthernet interface fa0/0 of router 1 is wrongly configured.
5
A routing issue has occurred in your internetwork. Which of the following type of devices should be examined to isolate this error?
access point
host
hub
router
switch
6
Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured with the source MAC address 0050.7320.D632 and the destination MAC address 0030.8517.44C4. The packet inside the captured frame has an IP source address 192.168.7.5, and the destination IP address is 192.168.219.24. At which point in the network was this packet captured?
leaving host A
leaving ATL
leaving Dallas
leaving NYC
7
Refer to the exhibit. Host A wants to connect to host B on a different network. Which three IP addresses can be assigned to host A to enable this connectivity? (Choose three.)
172.16.11.36
172.16.11.95
172.16.11.88
172.16.11.70
172.16.11.64
172.16.11.67
8
Which statement is true about the running configuration file in a Cisco IOS device?
It affects the operation of the device immediately when modified.
It is stored in NVRAM.
It should be deleted using the erase running-config command.
It is automatically saved when the router reboots.
9
What three statements are true about network layer addressing? (Choose three.)
Network layer addressing uses a hierarchy.
It uses addresses that are 48 bits in length.
It is used by Ethernet switches to make forwarding decisions.
It does not support broadcasts.
It uses a method by which the network portion of an address can be identified.
Network layer addressing identifies each host distinctly.
10
Which option represents a point-to-point logical topology diagram?
11
The Layer 4 header contains which type of information to aid in the delivery of data?
service port number
host logical address
device physical address
virtual connection identifier
12
Refer to the exhibit. While configuring a network, a technician wired each end of a Category 5e cable as shown. Which two statements are true about this setup? (Choose two.)
The cable is suitable for connecting a switch to a router Ethernet port.
The cable is suitable for connecting dissimilar types of devices.
The cable is unusable and must be rewired.
The cable is terminated in a way that the transmit pin is wired to the receive pin.
The cable simulates a point-to-point WAN link.
13
Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0 through 172.16.159.255?
172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192
14
Which OSI layer manages data segments?
application layer
presentation layer
session layer
transport layer
15
Refer to the exhibit. A user wants to access the Internet from the PC. A part of the running configuration of the router is shown. Which default gateway IP address should be configured at the PC to enable this access?
10.1.192.1
10.1.192.2
10.1.192.54
192.31.7.1
16
Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.)
Router(config)# line vty 0 3
Router(config-line)# password c13c0
Router(config-line)# login
The entries specify three Telnet lines for remote access.
The entries specify four Telnet lines for remote access.
The entries set the console and Telnet password to "c13c0".
Telnet access will be denied because the Telnet configuration is incomplete.
Access will be permitted for Telnet using "c13c0" as the password.
17
Refer to the exhibit. In a network, Hosts A and B are exchanging segments at the transport layer. Which two statements are true about this exchange? (Choose two.)
Host A is transferring files to host B using FTP.
Host A will send the next segment containing data for this session starting with byte number 11.
The segment from the destination host indicates that 11 bytes have been received successfully.
Host A is initiating a Telnet session to host B.
Host B can send the next segment of the data starting with byte number 2.
18
Which three IPv4 addresses represent valid network addresses for a subnet? (Choose three.)
192.168.9.64/28
192.168.9.146/28
192.168.9.96/28
192.168.9.129/26
192.168.9.51/26
192.168.9.64/26
19
Refer to the exhibit. Assume all devices are using default configurations. How many subnets are required to address the topology that is shown?
1
3
4
5
7
20
Refer to the exhibit. Which logical topology best describes the exhibited network?
star (kalau physical topology baru iki jawabannya)
ring
point-to-point
bus
mesh
21
Refer to the exhibit. The serial interface of the router was configured with the use of the commands that are shown. The router cannot ping the router that is directly connected to interface serial 0/0/0. What should the network technician do to solve this problem?
Configure the description at interface serial 0/0/0.
Configure an IP address on interface serial 0/0/0.
Remove the no shutdown command at interface serial 0/0/0
Reboot the router.
22
Refer to the exhibit. A host is connected to hub 1. Which combination of IP address, subnet mask, and default gateway can allow this host to function in the network?
IP address: 172.16.31.36 Subnet mask: 255.255.255.240 Default gateway: 172.16.31.35
IP address: 172.16.31.63 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
IP address: 172.16.31.29 Subnet mask: 255.255.255.248 Default gateway: 172.16.31.35
IP address: 172.16.31.32 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
IP address: 172.16.31.29 Subnet mask: 255.255.255.240 Default gateway: 172.16.30.1
IP address: 172.16.31.37 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35
23
Refer to the exhibit. What three statements are true about the IP configuration that is shown? (Choose three.)
The address that is assigned to the computer represents private addressing.
The computer is unable to communicate outside of the local network.
The network of this computer can have 126 hosts.
The prefix of the computer address is /27.
The IP address that is assigned to the computer is routable on the Internet.
The IP address that is assigned to the computer is a broadcast address.
24
Which OSI layers offers reliable, connection-oriented data communication services?
application
presentation
session
transport
network
25
Which three statements are true about network layer addressing? (Choose three.)
It uniquely identifies each host.
It assists in forwarding packets across internetworks.
It uses a logical 32-bit IPv4 address.
It is not a configurable address.
It is a physical address.
It identifies the host from the first part of the address.
26
As network administrator, what is the subnet mask that allows 510 hosts given the IP address 172.30.0.0?
255.255.0.0
255.255.248.0
255.255.252.0
255.255.254.0
255.255.255.0
255.255.255.128
27
Which password is automatically encrypted when it is created?
vty
aux
console
enable secret
enable password
28
Which three statements characterize the transport layer protocols? (Choose three.)
TCP and UDP port numbers are used by application layer protocols.
TCP uses port numbers to provide reliable transportation of IP packets.
UDP uses windowing and acknowledgments for reliable transfer of data.
TCP uses windowing and sequencing to provide reliable transfer of data.
TCP is a connection-oriented protocol. UDP is a connectionless protocol.
29
Which option would be a valid router hostname according to Cisco naming convention guidelines?
Rtr1_Bldg201
Building_201
Router 1
1st_Floor_Router_409_West_State_Street
Refer to the exhibit. The NAT functionality of the router is enabled to provide Internet access to the
PC. However, the PC is still unable to access the Internet. Which IP address should be changed to
209.165.201.1 to enable the PC to access the Internet?
192.168.1.191
192.168.1.101
192.168.1.1
192.168.1.254
31
Refer to the exhibit. On the basis of the IP configuration that is shown, what is the reason that Host A and Host B are unable to communicate outside the local network?
Host A was assigned a network address.
Host B was assigned a multicast address.
Host A and Host B belong to different networks.
The gateway address was assigned a broadcast address.
32
When connectionless protocols are implemented at the lower layers of the OSI model, what is usually used to acknowledge that the data was received and to request the retransmission of missing data?
IP
UDP
Ethernet
a connectionless acknowledgement
an upper-layer, connection-oriented protocol or service
33
Which three addresses belong to the category of public IP addresses? (Choose three.)
127.0.0.1
196.1.105.6
132.11.9.99
10.0.0.1
172.16.9.10
46.1.1.97
34
Which type of media is immune to EMI and RFI? (Choose two.)
10 Base-T
10 Base-2
10 Base-5
100 Base-FX
100 Base TX
1000 Base LX
35
Refer to the exhibit. What is required on host A for a network technician to create the initial configuration on Router1?
an FTP client
a Telnet client
a terminal emulation program
a web browser
36
Refer to the exhibit. The command that is shown was issued on a PC. What does the IP address 192.168.33.2 represent?
IP address of the host
default gateway of the host
IP address of the homepage for the host
primary domain name server for the host
IP address of the website resolver1.mooki.local
37
Refer to the exhibit. Host X is unable to communicate with host Y. Which command can be run at host X to determine which intermediary device is responsible for this failure?
telnet 192.168.1.1
ping 192.168.1.1
ftp 192.168.1.1
tracert 192.168.1.1
38
Refer to the exhibit. Host A sends a frame with the destination MAC address as FFFF.FFFF.FFFF. What action will the switch take for this frame?
It will drop the frame.
It will send the frame back to host A.
It will send the frame to all hosts except host A.
It will forward the frame to the default gateway.
39
Refer to the exhibit. What two facts can be determined from the session information that is displayed?(Choose two.)
The protocol is a connection-oriented protocol.
This exchange is part of the three-way handshake.
The SYN flag is representing the initial establishment of a session.
The destination port indicates that a Telnet session has been initiated.
The source port does not support communication with the destination port that is listed.
40
Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?
Connection 1 - straight-through cable Connection 2 - straight-through cable Connection 3 - crossover cable
Connection 1 - straight-through cable Connection 2 - crossover cable Connection 3 - rollover cable
Connection 1 - crossover cable Connection 2 - rollover cable Connection 3 - straight-through cable
Connection 1 - crossover cable Connection 2 - straight-through cable Connection 3 - crossover cable
Connection 1 - straight-through cable Connection 2 - rollover cable Connection 3 - crossover cable
41
Refer to the exhibit. Host A wants to access e-mail. Which destination socket number will be used to communicate this request?
10.10.1.2:53
0007.A7B8.0008:25
10.10.1.3:23
10.10.1.3:25
(Socket number= ip + port addres)
42
Refer to the exhibit. Host A wants to access the Internet. Which combination of a Layer 2 address and a Layer 3 address will enable this access from host A?
Destination MAC: 0030.8596.DE83 Default gateway: 209.165.202.130
Destination MAC: 0030.8596.DE82 Default gateway: 172.16.9.2
Destination MAC: 0030.8517.44C4 Default gateway: 172.16.1.1
Destination MAC: 0030.8517.44C4 Default gateway: 209.165.202.130
43
A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of password would require this login and be considered the most secure?
console
enable
enable secret
VTY
44
What are three characteristics of CSMA/CD? (Choose three.)
Devices listen to the media and transmit data only when they cannot detect another signal on the media.
All devices on the media can hear all communications.
Devices communicate based on a configured priority.
After a collision occurs, the devices that caused the collision have first priority when attempting to retransmit.
When a collision occurs, all devices stop transmitting for a randomly generated period of time.
CSMA/CD uses a token system to avoid collisions.
45
Refer to the exhibit. A PC is connected to a network. Which action will verify that the PC can communicate with its default gateway?
Use the ping 127.0.0.1 command.
Use the ipconfig command.
Use the ipconfig/all command.
Use the ping 10.0.0.254 command.
46
Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1 using Telnet. Which statement is true about this connection?
The data is automatically encrypted.
A Telnet server process is running on PC1.
The connection is made through a VTY session on the router.
A GET request was sent to RouterB to retrieve data during this session.
47
Refer to the exhibit. A technician is working on a network problem that requires verification of the router LAN interface. What address should be pinged from this host to confirm that the router interface is operational?
127.0.0.1
192.168.64.196
192.168.254.1
192.168.254.9
192.168.254.254
48
Refer to the exhibit. Which two facts can be determined about the topology? (Choose two.)
Three networks are needed.
Two logical address ranges are required.
A single broadcast domain is present.
Three collision domains are present.
Four networks are needed.
49
Which range of port numbers is assigned dynamically to client applications when initiating a connection to the server?
0 to 255
0 to 1023
1024 to 49151
greater than 65535
50
What are two functions of the data link layer? (Choose two.)
It segments and reorders the data.
It exchanges data between programs that are running on the source and destination hosts.
It controls how data is placed onto the media.
It generates signals to represent the bits in each frame.
It encapsulates each packet with a header and a trailer to transfer it across the local media.
51
A network technician wants to configure an IP address on a router interface by using the ip address 192.168.1.0 255.255.255.0 command. Which prompt should the technician see when entering this command?
Router>
Router(config-if)#
Router#
Router(config)#
52
What is the result of using the clock rate 56000 command at the serial interface of the router?
The interface is configured as a DCE device.
The interface timers are cleared.
The FastEthernet interface is made to emulate a serial interface by assigning it a timing signal.
The IP address for the serial interface is configured.
0 nhận xét:
Post a Comment