5:44 AM
Unknown
http://p4s-ccna.blogspot.comhttp://testccna-4u.blogspot.com 1. Refer to the exhibit. What two conclusions can be drawn from the output that is shown? (Choose two.) Both of the directly connected routes that are shown will share the same physical interface of the router. Inter-VLAN routing between hosts on the 172.17.10.0/24 and 172.17.30.0/24 networks is successful on this network.2. A router has two FastEthernet interfaces and needs to connect to four VLANs in the local network. How can this be accomplished using the fewest number of physical interfaces without unnecessarily decreasing network performance? Implement a router-on-a-stick configuration.3. What is important to consider while configuring the subinterfaces of a router when implementing inter-VLAN...
Monday, May 18, 2009
Thursday, May 14, 2009
CCNA v4 - E3 - Module 5 (100%)
http://p4s-ccna.blogspot.comhttp://testccna-4u.blogspot.com 1. What three link types have been defined for Rapid Spanning-Tree Protocol? (Choose three.) shared edge-type point-to-point2. What Rapid Spanning Tree Protocol (RSTP) role is assigned to the forwarding port elected for every switched Ethernet LAN segment? designated3. How can a network administrator influence which STP switch becomes the root bridge? Set the switch priority to a smaller value than that of the other switches in the network.4. Refer to the exhibit. What can be determined from the output shown? The priority was statically configured to identify the root.5. Which three statements are accurate regarding RSTP and STP? (Choose three.) Both RSTP...
Sunday, May 10, 2009
CCNA v4 - E3 - Module 4 (100%)
http://p4s-ccna.blogspot.comhttp://testccna-4u.blogspot.com1. Which statement is true when VTP is configured on a switched network that incorporates VLANs? VTP dynamically communicates VLAN changes to all switches in the same VTP domain.2. What are two features of VTP client mode operation? (Choose two.) unable to add VLANs can forward VLAN information to other switches in the same VTP domain3. Which three VTP parameters must be identical on all switches to participate in the same VTP domain? (Choose three.) domain name domain password version number4. What does a client mode switch in a VTP management domain do when it receives a summary advertisement with a revision number higher than its current revision number? It...
Friday, May 8, 2009
CCNA v4 - E3 - Module 3 (100%)
http://p4s-ccna.blogspot.comhttp://testccna-4u.blogspot.com1. What switch port modes will allow a switch to successfully form a trunking link if the neighboring switch port is in "dynamic desirable" mode? on, auto, or dynamic desirable mode2. Refer to the exhibit. Computer 1 sends a frame to computer 4. On which links along the path between computer 1 and computer 4 will a VLAN ID tag be included with the frame? C, E3. Refer to the exhibit. The exhibited configurations do not allow the switches to form a trunk. What is the most likely cause of this problem? The trunk cannot be negotiated with both ends set to auto.4. What must the network administrator do to remove Fast Ethernet port fa0/1 from VLAN 2 and assign it to VLAN 3? Enter the switchport...
Tuesday, May 5, 2009
CCNA v4 - E3 - Module 2 (100%)
http://p4s-ccna.blogspot.comhttp://testccna-4u.blogspot.com1. Which two statements about Layer 2 Ethernet switches are true? (Choose two.) Layer 2 switches have multiple collision domains. Layer 2 switches can send traffic based on the destination MAC address.2. Which command line interface (CLI) mode allows users to configure switch parameters, such as the hostname and password? global configuration mode3. Which two statements are true about EXEC mode passwords? (Choose two.) The enable secret password command provides better security than the enable password. The enable password and enable secret password protect access to privileged EXEC mode.4. Where is the startup configuration stored? NVRAM5. Refer to the exhibit....
Monday, May 4, 2009
CCNA v4 - E3 - Module 1 (100%) => latest version
http://p4s-ccna.blogspot.comhttp://testccna-4u.blogspot.com1. A network administrator is selecting a switch that will operate at the network core. Which three features should the switch support for optimum network performance and reliability? (Choose three.) 10 Gigabit Ethernet quality of service (QoS) hot-swappable hardware 2. Refer to the exhibit. Beginning with HR servers and workstations, a network engineer is designing a new security structure for the network. Which set of policies adheres to the hierarchical network model design principles? Configure port security options on S1. Use Layer 3 access control features on D1 and D2 to limit access to the HR servers to just the HR subnet.3. Which layer of the OSI model does an access layer...
Friday, May 1, 2009
CCNA lab
CCNA CertificationThe Cisco CCNA network associate certification validates the ability to install, configure, operate, and troubleshoot medium-size routed and switched networks, including implementation and verification of connections to remote sites in a WAN. This new curriculum includes basic mitigation of security threats, introduction to wireless networking concepts and terminology, and performance-based skills. This new curriculum also includes (but is not limited to) the use of these protocols: IP, Enhanced Interior Gateway Routing Protocol (EIGRP), Serial Line Interface Protocol Frame Relay, Routing Information Protocol Version 2 (RIPv2),VLANs, Ethernet, access control lists (ACLs) * 1 Console Login * 2 Router Configuration *...
